F@ST 3000 - Modem SAGEM - Free user manual and instructions

USER MANUAL F@ST 3000 SAGEM

13 Internet access Configuration

Quick Configuration

‘Internet Service Provider' parameters

These parameters are required to access the Internet. They are provided by your ISP. Please refer to your subscription.

User Name |fti/gt4gg3t

Password**********

Cancel Exit Next >>

14 Internet access Configuration (cont.)

• Enter the parameters delivered by your Internet Access Provider or keep the default values (VPI, VCI, Protocol and encapsulation).
• Click Next to continue the configuration.

16 Voice over IP (VoIP) Configuration of your SAGEM F@st™ 3000

• Click H323 in the VoIP menu; the following screen appears.

• Click Select then on the Modify button to enter the parameters delivered by your Internet Access Provider (IAP).

1 Pack - Unit Presentation

Your pack includes the following elements:

The SAGEM F@st™ 3000 Residential Gateway presents in rear panel, the connectors for the following connections :

ADSL Line item 2,
VoIP telephone line item 3,
- Mains adapter unit item 4,
- Ethernet connection item 8,
USB connection item 9.

On the SAGEM F@st™ 3000, the display LEDs indicate the active / inactive state of the power supply, ADSL line, Ethernet, USB and telephone interfaces.

3 Connection of the telephone terminal on VoIP

• Connect the second telephone set to the PHONE connector in using the phone adaptor (6).

2 Setting-up of the filter and connection of the ADSL line

• Connect the ADSL line lead (3) to the LINE connector of the SAGEM F@st™ 3000.

4 Powering up the residential gateway

• Connect the mains adapter unit cable to the PWR socket on the rear panel of the residential gateway.
• Set the On/Off (I/O) switch to On (the «I» position). The PWR LED comes on.

5 ADSL Synchronization

In less than two minutes, the Residential Gateway synchronizes automatically with your ADSL line. The LINE LED is then lit on steady.

6 Lauching CD-ROM

• Insert the CD-ROM in your computer's appropriate drive; the following screen appears.

• Click Configure your computer (step 1).

7 Interfaces choice

The following screen appears :

Choose which computer's interface will be used to connect your SAGEM F@st™ 3000:

• Ethernet (selection of the network card),
  USB (drivers' installation).

Remark: If your computer is equipped with an Ethernet card, we advise you to configure by the Ethernet port.

8 Configuring the Ethernet interface

• Click Ethernet then follow the displayed process.
• Connect as figure here after (at the right moment).

• Go to the item 11: Configure your SAGEM F@st™ 3000 (step 2).

9 Installation and Connection on USB

• Click USB ; the following screen appears:

SAGEM

Switch on your SAGEM F@st 3000 to complete the installation. Connect it to the USB port of your computer.

If your SAGEM F@st 3000 is already connected to the USB port of your computer, switch the F@st 3000 off then switch it on again.

Finish

• Connect as figure here after (when that asks you).

11 Access to your SAGEM F@st™ 3000 (continue)

In the "UserID field", enter root and in the "Password" field, enter 1234.
- Then click OK to valid.

Remark: The bar of the screen shows the equipment's IP address (192.168.30.1).

10 Access to your SAGEM F@st™ 3000

When the configuration of your computer (step 1) is done, you proceed to the step 2.

• Click Configure your SAGEM F@st™ 3000.

12 Configure your SAGEM F@st™ 3000

The welcome screen appears.

• Click the Quick Setup button or select Quick Setup from the list on the left of the screen.

17 Voice over IP (VoIP) Configuration of your SAGEM F@st™ 3000 (cont.)

• Enter the following parameters: Phone No., H323 Id., Codec.
  Then click the Submit button.

• Click the

Modify RG

button.

19 Voice over IP (VoIP) Configuration of your SAGEM F@st™ 3000 (cont.)

• Select the "Use GateKeeper" field.
• Enter the primary address provided by your Internet Access Provider (IAP).
• Click the submit button to take the parameters entered into account.

The following screen appears.

• Verify the parameters entered.

18 Voice over IP (VoIP) Configuration of your SAGEM F@st™ 3000 (cont.)

In the scroll down list of the "Interface" field, select ppp0 (don't take the reboot invit into account).
- Check the box of the "Advanced" field.
- Select the "Enable Fast Start" field.
In the "Max Dialled Digits" field, enter the desirated value.

20 Voice over IP (VoIP) Configuration of your SAGEM F@st™ 3000 (cont.)

• Select Quick Status from the list on the left of the screen; the following screen appears.

• In normal operation, the Internet Access and VoIP Access status are displayed in green characters respectively "Internet Access enabled" and "VoIP enabled".
  You can now surf and/or phone on Internet.